BLI 1682 GoPack! Power Continuity Capacitor Pack with plug


Description

Do you have
intermittent power problems with your layouts? Be it dirty track, pesky
frogs or switches, GoPack! provides power to your locomotive even when your
layout doesnt. Designed specifically for Paragon3TM locomotives, just plug
GoPack! into the onboard port on the locomotive and enjoy continuous power,
no matter what layout youre on. Each GoPack! provides between 2-6 seconds
of uninterrupted power.

Controllable for DCC: When used with a Paragon3
Revision H or above decoder, GoPack! has programmable CVs which allow your
locomotive to be programmed on the program track even with GoPack! onboard.

 

Dimensions:
30mm x 13mm x 9mm

 

 

Frequently Asked Questions:

Which models
can accept a GoPack?

HO Scale Paragon2 and Paragon3 (Revision
E and lower Paragon3 decoder boards) can have the GoPack added via solder
points. The solder points for the aforementioned decoders are under
Technical
Update Bulletins
on
our website.

HO Scale Paragon3 models (Revision H and above Paragon3 decoder boards)
have a socket to accept the wiring from a GoPack making it a PlugNPlay
device with no soldering involved.


There is no GoPack for N Scale models at this time.

How do I know which decoder board revision is in my model?

If your models box has the Accepts GoPack logo you
have a Revision H board installed.

If
your model's box has this logo on it, GoPack! is plug and play.

 

If you see the small socket directly next to the speaker
output socket on the decoder you have a revision H board.


If you look at the top of the decoder, you will see HO-300-X whatever
is in the place of X is what your board revision is.

Which models are GoPack Ready for plug and play
operation?

Models with the Accepts GoPack! logo have the Revision H
or above board (which means it has the socket), and weve done the work to
ensure there is enough space under the shell for it to fit under there.

Will the GoPack! affect my
ability to program on the program track?

Programming on the mainline is no problem with the GoPack!
However, if you'd like to read/write CV's on the program track in Paged
Mode and/or Direct Mode you can either set CV221 to disable the GoPack!
and then let the capacitors discharge (Revision H decoders and above only)
or for a solder type installation you can either wire an On/Off switch
in-line, or unplug the wiring from the GoPack! socket while programming.

Can I send my revision E decoder in for a Revision H
decoder?

Yes, no problem and just a $20 S&H fee (or $35
International) its a one-for-one swap as long as the Revision E decoder
is working when it arrives. If the board arrives defective, there is a $99
fee for an out-of-warranty replacement decoder in addition to the cost of
the GoPack.

Can I send my model in for you to add a GoPack for me?

Yes, there is a flat rate $89 fee that covers all parts,
labor, and shipping back to you for this service. You would be responsible
for shipping the model to us.

Can I use the GoPack on models that were not manufactured
by BLI?

Weve not tested for this, and would not guarantee any
compatibility with other models.

Which BLI models cannot work with the GoPack?

Blueline, PCM, and QSI equipped models are not compatible
with the GoPack only Paragon2 and Paragon3 HO Scale.

GoPack! Introduction and Usage

New Page 1


GoPack! Installation - Paragon3 Rev H and Above Decoder

New Page 1


GoPack! Installation - (Soldering Method For Paragon2 and Paragon3 Models)

Estimate shipping

You may also like

Recently viewed